Abgasanalyse
Portable FTIR gas analyser

Multi-component, multi-range portable FTIR gas analyser

Measure 1000’s of gases with single unit

Software offers no-limit on number of gas measurements at once, using powerful PLS algorithms

Data can be downloaded and re-analysed offline for new gases

Built in O2 sensor, heated inlet filter and sampling control

Specific Applications for atmosFIR:

  • Stack Emission Testing
  • Incineration and Combustion Gas Monitoring
  • RealTOC measurement
  • Speciated VOC with use of high resolution
  • Abatement plant efficiency – inlet and outlet
  • Ambient air monitoring from 0.5ppm
  • Siloxane Measurements
Portable FTIR gas analyser

Standard Application Model for common emission gases
Hardcoded analysis, no complex set-up required Switch on > Zero > Measure > Report

Component

Ranges /

mg/m3

Lower detection Limit (LDL) /

mg/m3

CO 0-75; 0-1000 0.6
NO 0-200; 0-600 1.0
NO2 0-200; 0-600 0.6
N2O 0-50; 0-400 0.4
SO2 0-75; 0-1000 0.6
NH3 0-15; 0-50 0.1
HCl 0-15; 0-100 0.2
HF 0-15; 0-50 0.2
CH4 (Methane) 0-50; 0-1000 0.1
C2H6 (Ethane) 0-50; 0-1000 0.1
C3H8 (Propane) 0-50; 0-1000 0.8
C2H4 (Ethene) 0-50; 0-1000 0.4
HCHO (Formaldehyde) 0-20; 0-100 0.2
TOC (Indication only) 0-50; 0-1000 -
H2O 0-40% 0.02%
CO2 0-20% 0.005%


 

Portable FTIR gas analyser
Portable FTIR gas analyser
Portable FTIR gas analyser
Portable FID analyzer

Portable FID analyzer model OVF-3000 by J.U.M. Engineering

  • Lightweight internal fuel storage, easy to operate
  • Fully heated to 180°C
  • Typical sensitivity 0.01 ppm CH4
  • Internal sample pump and air pump
  • Internal combustion air supply (No external air cylinder needed)
  • Disposable sample filter in front panel
  • Automatic flame out alarm contact and fuel shut off
  • Sample pressure regulator not in contact with sample gas
  • Multiple range capability; 5 selectable ranges are standard

Applications

  • Stack gas emissions and all other Environmental and process applications
  • Air and gas scrubber efficiency
  • Process chemical gas analysis
  • Personnel safety
  • Solvent recovery
  • Catalytic converter and thermal combustor testing
  • Automotive and engine emissions
  • Fence line (perimeter) monitoring

Complies analytically with EN 12619, EN 14181/ EN ISO 14956, (EU) and with EPA Method
25A and Method 503 (USA)

Portable FID analyzer
Method Heated Flame Ionization Detector (HFID)
Sensitivity Max. 1 ppm CH4 full scale (100 ppb lowest detectable)
Response time @ sample inlet <0.2 seconds
t90 time @ sample inlet <1.2 seconds
t90 time including 4X6mm sample line Including heated sample line (7.5m) and sample probe filter: less than 8 seconds
Zero drift <2% full scale / 24h
Span drift <2% full scale / 24h
Linearity Up to 10.000 ppm full scale within 1.5%
Oxygen synergism < 2% FSD
Measuring ranges (ppm) Front panel turn switch: 0-10,100, 1.000, 10.000,
100.000, others on request.
Signal outputs 0-10 VDC, 4-20 mA, including RS-232 data output
Display 6- digit direct reading ppm units capability to measure up to three (3) overlapping measuring ranges without range
change
Total sample flow through 2.5 to 2.8 l/min capacity @ operating temp.
Sample filter Disposable change filter in rear panel. Option OVE 32
Zero and Span gas Front panel switch selectable and remote control, gas
inlets on rear panel
Zero and span adjust Manual duo dial on front panel
Fuel gas 100% H2, consumption approx. 20 ml/min
Burner air consumption Built in burner air supply. No external cylinder air needed.
consumption approximately 130 ml/min, all mixed fuel
gases approx. 220 ml/min
Oven temperature 180°C (374°F)
Temperature control micro-processor PID controller
Power requirements 230VAC/50Hz, 850W (120 VAC/60Hz optional)
Ambient temperature 5-43°C (41-110°F)
Dimensions (W x D x H) 445 mm x 220 mm x 350 mm
Weight approx. 13 kg





 

Attachments

Portable FID analyzer
Portable FID analyzer
Portable FID analyzer

Datalogging

To log the 0-10V and/or 4...20mA analog  outputs.

PC-powered: Over USB Software-based J.U.M. MhcLog-109 (dual channel)

Hand held battery powered: Ahlborn ALMEMO 2590

Heated Prefilter

Heated prefilter model VE112 by J.U.M. Engineering.

1 Heated sample inlet

2µm stainless steel sampler filter

5 'hot' outlets for gas cooler, FID, FTIR

Integrated heated sample pump 12l/min

Ideal for stationairy or transportable CEM's (Continuous Emission Monitoring system)

Heated Prefilter
Weight Approx. 25kg (55 lbs)
Dimensions (W x D x H) 19" (483 mm) x 460 mm x 221 mm
Sample filter material All stainless steel 316SS
Filter pore size 2μm
Sample valves All stainless steel/Viton®
Purge air valve All brass, Plunger and plunger housing stainless steel, seals made from Viton®
Calibration gas valve All brass, or to be specified. Plunger and plunger housing
stainless steel, seals made from Viton®
Sample pump All stainless steel, diaphragm and valves made from Viton®
Sample pump Capacity 12 l/min, unrestricted flow
Oven Temperature 190°C (374°F), electronic temperature controller
Oven Temperature Output 0-5 VDC @ 10mV/°C
Power Requirements 230VAC/50Hz, 1250W (115VAC/60Hz, 850W)
Ambient Temperature 5-43°C (41-110°F)

Available Options

EPC 11 Remote control for sample pump. Pump can be switched on and off externally if Instrument is in external mode.
APO 11 Built in automatic programmable back-purge timer for the sample filter
COS 11 Overflow calibration system for EPA CFR 40, Method 25A
TPR 11 Built in temperature controller for J.U.M. heated sample lines Model TJ 100
and TJ 100A; EXTERNAL MODULE ONLY ON VE 112A!





 

Attachments

Heated Prefilter
Heated Prefilter
Heated Prefilter

Rugged transport case for mobile use (e.g. for mobile FTIR)

Beheizter Probenahmeschlauch

Jumatherm beheizter Probenahmeschlauch mit austauschbarer PTFE Innenseele

Robuster Trägerschlauch

Silicongummi Endkappen

Isolierung mit Filz und 7mm Siliconschaum

Außenschutzgeflecht Polyamid oder VA

Leistungsaufname 100W/m

Länge nach Wunsch (1 bis 35m oder länger in Sonderausführung)

Zugentlastungsseil unter den Siliconenschaum mitgeführt

Optionen

Feste oder austauschbare PTFE Seele

Zweite Seele z.b. als Kalibrationsleitung

Interne Steuerleitung

Durchmesser Innenseele 6mm, 8mm oder Größer

Zwei beheitzte Seelen statt einer

Edelstahl Einschraubstück als Knickschutz der Innenseele Ex-Schutz

Interne Leitung aus PFA statt PTFE

Beheizter Probenahmeschlauch
Beheizter Probenahmeschlauch
Beheizter Probenahmeschlauch
Beheizter Probenahmeschlauch
JUM FID 109A TOC-Analysator
JUM FID 109A TOC-Analysator, 2 Detektoren für TOC, Methan und NMHC gleichzeitige Messung, Gewicht ca. 25kg
JUM FID 109A TOC-Analysator

Attachments

JUM FID 109A TOC-Analysator
JUM FID 109A TOC-Analysator
JUM FID 109A TOC-Analysator

Rugged transport case for mobile use.

Datalogging

To log the 0-10V and/or 4...20mA analog  outputs.

PC-powered: Over USB Software-based J.U.M. MhcLog-109 (dual channel)

Hand held battery powered: Ahlborn ALMEMO 2590

HovaCal® Gasmischer mit Verdampfereinheit
HovaGas Gasmischer/-verdünner für trockene Gase. HovaCal® Gasmischer mit Verdampfereinheit zur Herstellung genauer Konzentrationen H2O, HCl, HF, NH3, HgCl2 und Gemische von SO2, NOx, CO, CO2 und O2. Eingebaut in einem sehr robusten Tragekoffer. Beispielapplikationen: - Kalibation vor Ort von CEMS - Nullpunkt und Spankalibration - Driftüberprüfung - Querempfindlichkeiten und Feuchteeinfluss - Linearitätstests
HovaCal® Gasmischer mit Verdampfereinheit
HovaCal® Gasmischer mit Verdampfereinheit
HovaCal® Gasmischer mit Verdampfereinheit
HovaCal® Gasmischer mit Verdampfereinheit
Analyse-Faltenbalgpumpen

Die M&C Faltenbalgpumpen sind für die besonderen Anforderungen in der Analysentechnik ausgelegt. Die Pumpen sind dabei speziell zur Förderung korrosiver Gase geeignet.

Spezifische Merkmale
• Medium- korrosivgeschützte Materialien
• Schmierstofffreiheit zur Reinhaltung des geförderten Gases
• Wartungsfreie Konstruktion
• lange Standzeiten
• Sehr niedrige Wartungskosten

Die Pumpen weisen variable Anschlüsse auf – entweder seitlich oder oben auf dem Pumpenkopf. Die Pumpenkopfmontage kann beliebig in 90 Grad-Schritten erfolgen.Diese M&C-Neuprodukte sind ab sofort in 16 Versionen, 230 V oder 115 Volt sowie zwei Leistungsvarianten erhältlich. Weitere Varianten und Produktzulassungen hat M&C  in Vorbereitung.Ein detailliertes Datenblatt und eine Betriebsanleitung stehen zur Verfügung. Weitere Vertiefungsinformationen sind abrufbar bei den technischen Beratern der M&C in Ratingen. Oder auch dem flächendeckenden M&C-Außendienst im gesamten deutschsprachigen Raum. Und natürlic

Analyse-Faltenbalgpumpen
Analyse-Faltenbalgpumpen
Analyse-Faltenbalgpumpen
Analyse-Faltenbalgpumpen
HovaPOR Verdampfer
Die HovaPOR Verdampfer erzeugt pulsationsfreie Dampf- oder Gasdampfgemische. Je nach Anwendung werden unterschiedliche Typen und Prinzipien verwendet. Wichtig für die Auswahl des Verdampfers ist die Flüssigkeitsströmung, der Art der Flüssigkeit, der Temperatur und dem Druck. Wir verwenden im Allgemeinen drei verschiedene Verdampfungs Prinzipien: Gasinnen Ultraschall- Druck unterstützt Basis eines guten Verdampfung ist eine angepasste Flüssigkeitsabgabe. Deshalb bieten wir für jedes Problem der Verdunstung ausreichende Flüssigkeitsfördermodul. Neben Wasser werden die HovaPOR Verdampfer geeignet für: Kraftstoff Alkohol und organischen Lösemitteln wässrige Säuren und Lösungen Silizium Titan-organischen Verbindungen
HovaPOR Verdampfer
HovaPOR Verdampfer
HovaPOR Verdampfer
HovaPOR Verdampfer
Testo 350 industrial flue gas analyser
Testo 350 industrial flue gas analyser with integrated gas conditioning system. The unit consists of a control unit and and analyzer box. The analyzer box can be equipped with up to 6 sensors. Possible sensors are: CO, CO2, NO, NO2, SO2, H2S and CxHy. The testo 350 analyser has been specially developped for: Engine testing Boiler and burner tuning Industrial processes testing Turbine testing
Testo 350 industrial flue gas analyser
Type K (NiCr-Ni) Range -200 … +1370 °C Precision ±0,4 °C (-100 … +200 °C) ±1 °C (-200 … -100,1 °C) ±1 °C (200,1 … +1370 °C) Resolution 0,1 °C (-200 … +1370 °C) Differential pressure Range -40 … +40 hPa -200 … +200 hPa Precision ±1,5 % v. Mw. (-40 … -3 hPa) ±1,5 % v. Mw. (+3 … +40 hPa) ±0,03 hPa (-2,99 … +2,99 hPa) ±1,5 % v. Mw. (-200 … -50 hPa) ±1,5 % v. Mw. (+50 … +200 hPa) ±0,5 hPa (-49,9 … +49,9 hPa) Resolution 0,01 hPa (-40 … +40 hPa) 0,1 hPa (-200 … +200 hPa) Absolute pressure Range 600 … +1150 hPa Precision ±10 hPa Resolution 1 hPa O₂ Range 0 … +25 vol.% Precision ±0,8% of fsv (0 … +25 vol.%) Resolution 0,01 vol.% (0 … +25 vol.%) Reaction time t₉₀ 20 s (t95) CO (H₂ compensated) Range 0 … +10000 ppm Precision ±5 % v. Mw. (+200 … +2000 ppm) ±10 % v. Mw. (+2001 … +10000 ppm) ±10 ppm (0 … +199 ppm) Resolution 1 ppm (0 … +10000 ppm) Reaction time t₉₀ 40 s CO low meting (H₂-compensated) Range 0 … 500 ppm Precision ±5 % v. Mw. (+40 … +500 ppm) ±2 ppm (0 … +39,9 ppm) Resolutie 1 ppm (0 … +500 ppm) Reaction time t₉₀ 40 s NO-meting Range 0 … +4000 ppm Precision ±5 % v. Mw. (+100 … +1999 ppm) ±10 % v. Mw. (+2000 … +4000 ppm) ±5 ppm (0 … +99 ppm) Resolution 1 ppm (0 … +4000 ppm) Reaction time t₉₀ 30 s NO low Range 0 … +300 ppm Precision ±5 % v. Mw. (+40 … +300 ppm) ±2 ppm (0 … +39,9 ppm) Resolution ±0,1 ppm (0 … +300 ppm) Reaction time t₉₀ 30 s NO₂ Range 0 … +500 ppm Precision ±5 % v. Mw. (+100 … +500 ppm) ±5 ppm (0 … +9,99 ppm) Resolution 0,1 ppm (0 … +500 ppm) Reaction timet₉₀ 40 s SO₂ Range 0 … +5000 ppm Precision ±5 % v. Mw. (+100 … +2000 ppm) ±10 % v. Mw. (+2001 … +5000 ppm) ±5 ppm (0 … +99 ppm) Resolution 1 ppm (0 … +5000 ppm) Reaction time t₉₀ 30 s
Testo 350 industrial flue gas analyser
Testo 350 industrial flue gas analyser
Testo 350 industrial flue gas analyser
Heated FID analyser J.U.M. 3-300A

Heated FID analyser for TOC measurements.

TÜV approved for 2. BImSchV. 13. BImSchV and 17. BImSchV, fully complies with EN 12619, EN 13526 (EU) and EPA Method 25A and Method 503 (USA).

Heated FID analyser J.U.M. 3-300A

Features

  • Maintenance free sample filter back purge system allows filter to be cleaned without dismantling (automatic optional)
  • Built in burner air generator, no external air cylinder needed
  • All components in contact with sample fully heated and controlled at 190 degree C
  • Built-in sample pressure and sample pumps
  • Automatic flame out alarm and contact
  • Fast response within 1 second
  • Low fuel consumption
  • Very selective
  • Microprocessor controlled PID-type temperature controller
  • Remote control for sample, calibrate and back purge is standard
  • Remote or automatic range change optional

Applications

  • Stack gas hydrocarbon emissions monitoring
  • Fence line monitoring
  • Raw exhaust vehicle emissions analysis
  • Catalytic converter testing
  • Measuring engine combustion efficiency
  • Hydrocarbon contamination monitoring in air and other gases
  • Carbon adsorption regeneration control
  • Detection of trace hydrocarbons in purity gases used in the semi conductor industry
  • LEL monitor of solvent laden air

Attachments

Heated FID analyser J.U.M. 3-300A
Heated FID analyser J.U.M. 3-300A
Heated FID analyser J.U.M. 3-300A

Rugged transport case for mobile use. Front and back panel removable for easy access and operation.

JUM 3-00A with case

Datalogging

To log the 0-10V and/or 4...20mA analog  outputs.

PC-powered: Over USB Software-based J.U.M. MhcLog-109 (dual channel)

Hand held battery powered: Ahlborn ALMEMO 2590

Horiba PG350E tragbarer Gasanalysator
Gasanalysator NOx, SO2, CO, CO2, O2 Nach EN 15267-3 en EN 14181 MEssverfahren nach SRM (Standard reference method) für CO (EN 15058) O2 (EN14789) NOX (EN 14792)
Horiba PG350E tragbarer Gasanalysator
Meetprincipes: NOx: Cross-Flow Modulation Chemiluminescence Detection Method SO2, CO: Cross-Flow Modulation Non-Dispersive Infrared Absorption Method CO2: Non-Dispersive Infrared Absorption Method O2: Galvanic, Zirconia or Paramagnetic Method Measuring ranges (standard model) NOx A-range 0-25/50/100/250/500/1000/2500ppm(standard spec.) B-range 0-50/100/250/500/1000/2500/5000ppm SO2: 0-200/500/1000ppm CO A-range 0-200/500/1000/2000/5000ppm (standard spec.) B-range 0-0.5/1/5/10/15 vol% (B-range is not available for PG-350) CO2: 0-5/10/20 vol% O2 0-5/10/25 vol%(Galvanic or Zirconia method) 0-10/25 vol%(Paramagnetic method)
Horiba PG350E tragbarer Gasanalysator
Horiba PG350E tragbarer Gasanalysator
Horiba PG350E tragbarer Gasanalysator

Transport case